| FRP采光板安装方法 |
| 添加时间：2018/10/26 14:14:47 浏览次数： |
| 1.采光板在固定前需先导孔，孔径必须大于固定螺丝直径的6-9mm，以作为热胀冷缩之用。 1. The guide hole is needed before fixing the lighting board. The aperture must be 6-9mm larger than the diameter of the fixing screw to be used for thermal expansion and cold contraction. 2.采光板采用铝型材扣件固定,波形采光板采用采光板支架和自攻螺钉连接固定,再打胶密封。采光板的位置一般设置在跨中。 2. The lighting plate is fixed with aluminum fasteners, and the wavy lighting plate is fixed with the lighting plate support and self-tapping screws, and then sealed with glue. The location of daylighting board is usually placed in the middle span. 3.采光板与钢板在纵向搭接时，最小必须有200mm的重叠，并贴置两条止水带。 3. when light panels and steel plates are longitudinally lapped, 200mm overlap must be the minimum and two water stop zones are attached. 4.采光板与自攻螺钉连接,必须有盖板。阳光板冷热变形较大,容易被自攻钉剪破,因此阳光板在打自攻钉处应开较大孔。在安装采光板时要考虑采光板的伸缩性。 4. the lighting plate must be covered with self tapping screws. Sunshine plate is easy to be cut by self-tapping nails because of its large deformation in cold and hot conditions. Therefore, sunshine plate should have larger holes in the place of self-tapping nails. The flexibility of light panels should be considered when installing daylighting panels. 5.采光板固定时，必须使用良好的泛水垫圈，使之介于螺丝与采光板之间，以便于防水防尘。将泛水垫圈套入螺丝内以后，用电钻锁入檩条内，即完成采光板的固定工作。 5. When fixing the lighting board, a good flooding washer must be used to make it between the screw and the lighting board in order to prevent water and dust. After the flooding washer is inserted into the screw, the electric drill is locked into the purlin, which completes the fixing work of the daylighting board. 6.采光板在12m以内无需搭接,超过12m则需要搭接,搭接长度为200-400mm,搭接处施涂二道密封胶,横向搭胶不需收边,纵向彩钢板的搭接需看板型,普通压型钢板,一般不考虚做收边,直接将其与彩板用自攻钉固定,并施涂密封封胶,咬合板则需做收边。 6. Daylight plate within 12 m need not overlap, more than 12 m need to overlap, overlap length of 200-400 mm, overlap the application of two sealants, lateral overlap does not need to close, vertical color steel plate overlap need Kanban type, ordinary profiled steel plate, generally do not consider empty edge, directly with the color plate fixed with self-tapping nail, and apply sealant, bite board rules We need to collect edges. 7.采光板施工时，严禁脚直接踩在波峰上，以免采光板开裂。必须在采光板的横向位置，放置一块1200mmx300mm{长x宽)防滑厚木板，脚踩在其上进行采光板的导孔和固定螺丝工作 7. when lighting panels are constructed, feet are not allowed to step on the crest directly so as not to crack the lighting boards. A 1200mm x 300mm {length x width} non-skid plank must be placed in the lateral position of the daylighting board on which the guide hole and the fixing screw of the daylighting board can be operated. |
| 上一页 采光板技术问答 |
| 下一页 在安装玻璃钢采光板时要考虑采光板的伸缩性 |
Copyright © 技术支持：遨游网络